WallaceP r e m i u m E d u c a t i o n a l G r e e n h o u s eAssembly Manuals for Models:16'(w) x 24'(d) x 11.5'(h)16'(w) x 3
Roof Purlin cont'dWhen installing roof purlin start from the front or rear and slide thepurlin through the U-bolts on the purlin hanger "L
Installing Eave ExtrusionEave extrusion is an aluminum channel that receives both the roof andsidewall polycarbinate sheets.Aluminum EaveExtrusionSID
Framing EndwallsEndwall studs will be pre-cut. Door headers, Door studs andhorizontal purlin will have to be field cut.Refer to the page(s) labeled
In the next page(s) you will see typical Endwall Layouts forthe "Scholar Series" greenhouse. Look these drawings overcarefully, if you do n
Endwall Layouts (FRONT ENDWALLS)5'16'6'-034" 6'-034"1'-10"6'-612"3'-612"3'-4"fr
Endwall Layouts (REAR ENDWALLS w/ EVAPORATIVE COOLING SYSTEMS)3' x 10' cooling system4' x 10' cooling system3' x 10' co
Sidewall Door MountingIf your Scholar has 8' sides plus an Evaporative Cooling System in the endwall, you will need to mount therear door in the
OPENING MEASUREMENTS FOR FANS, SHUTTERS AND DOORS {SUPPLIED BY ATLAS} Fan opening for: 18” Box wall “Quietaire” 24 1/2” High X 24 1/2” Wide 30” Sla
heaterhangersheater hanger bracket-slides to inside of end rafterand second rafter -secure using boltsand nuts providedheater hangerendrafterheater ha
VENT PIPE KIT FORNON-POWER VENTED HEATERSEND BOWHEATERWALL COLLARS18" MIN.2-PIECEELBOW4' PIECE1' MIN.ADAPTERPARTS GENERALLY REQUIRED1-
HEATER VENT PIPE FOR A POWER VENT HEATEREND BOWHEATERWALL COLLARS18" MIN.ADJUSTABLEELBOWADAPTERPARTS GENERALLY REQUIRED2- WALL COLLARS2- ADJUSTAB
Aluminum Base AngleAluminum BaseAngle1. Identify the 2''x 3'' Aluminum Base Angle (ABA). Note- ABA isin red on this page for ident
SECURING ALUMINUM BASE ANGLE TO FOUNDATIONUsing a metal cut bit, drill a 5/16" hole approximately every 18'' apart down the length of t
Installing Ridge BaseThe ridge base extrusion will attach to the peak of the greenhouseat each center connector.ridge baseextrusion1. Identify the Ri
Installing Ridge CapThe ridge cap extrusion will attach to the ridge base extrusionforming a channel to receive and hold the polycarbinate in place at
ATTACHING THE INTERMEDIATE RAFTER EXTRUSION2 3 Ridge Base Ridge Base Flange Rafter Extrusion 4 5 6 Intermediate Rafter Extrusion Tek-screw Attaching
16'wide Scholar PCSS sheet layout6' w X 10'h PCSS sheet6' w X 8'h PCSS sheet 6' w X 8'h PCSS sheetPage 24
COVERING ENDS WITH P.C.S.S. USING H-SPLICE3 2 1 4 IMPORTANT: Be sure to read the label on the P.C.S.S. covering to determine the side of the sheet tha
ATTACHING 1" X 1" ANGLE AROUND FAN AND SHUTTER OPENINGSMeasure the bottom of the opening and notch the 1" x 1" angle leaving 1&quo
ATTACHING END RAFTER EXTRUSION1 3 2 4 Apply foil tape to the top of the end rafter, allowing it to over-lap the top edge of the P.C.S.S. endwall cover
FOUNDATIONIMPORTANT: It is very important to begin with a level surface. Check your foundation to ensure itis level at every point. You must assure y
COVERING THE SIDEWALLS 1 2 4 3 Measure and cut the H-splice to fit between the Eave Extrusion and the Aluminum Base Angle. The H-splice overlaps th
ATTACHING 1" X 1" ANGLE AROUND BASEEducator(8'sides) Page 46 ms 10/09/07Identify and attach the 1"x 1" aluminum angle. This 1
ATTACHING THE CORNER FLASHING1 2 3 Applying the corner flashing Identify the 2" x 3" aluminum flashing (the same as the base angle we
INSTALLING P.C.S.S. ROOF COVERING3 1 After all extrusions are in place, snap the P.C.S.S. support brackets onto the purlins. Each purlin will receive
INSTALLING P.C.S.S. ROOF COVERING (CONT'D)1 3 2 At the end rafter and on the intermediate extrusions between each roof panel, you will need to a
HAF FAN INSTALLATION1 2 3 USE THE CHAINS PROVIDED TO ATTACH HAF FANS DIRECTLY TO THE BOW ASSRMBLY OR TRUSS CHORD. USING TEK SCREWS,SCREW THE CHAINS
PREVENTATIVE MEASURESEave extrusion Splice End of plastic locking cap Caulk around the corners Final Note: If the greenhouse is not put into operation
GROUNDRAIL ASSEMBLY1. Identify groundrail components: 1 front groundrail, 1 rear groundrail, 2 side groundrails or side rails
GROUNDRAIL ASSEMBLY cont'dfront/reargroundrailsfront/reargroundrails#14 tek screwsto attach front/reargroundrails to sidegroundrailsfront/reargro
CENTERCONNECTORBOLT HOLEfor RIDGEEXTRUSION#14 x1''TEKSCREWSHALF BOW (95'')14" NUTS516" x 2 12"CARRIAGE BOLT14"
Sidewall & Rafter Connections1. Identify legs for sidewalls:2'' x 2'' square tubing, quantity depending on order (refer to pac
2'' X 2'' TRUSS CHORD DETAIL forScholar with 8' sidesOnly Intermediate Legswill have trusses1. Identify truss chord (2'&
Sidewall & Roof PurlinSidewall Horizontal Purlin (2'' x 2'' square tubing) will need to be cutinto 70'' pieces, this
Commentaires sur ces manuels